Amplificador de clase D de nitruro de galio con diseño de filtro de abeto para subwoofer
Amplificador de 2 canales

Amplificador de clase D de nitruro de galio con diseño de filtro FIR para subwoofer

Artículo No.: D2-4500 DSP
Modelo: D2-4500 DSP
Canal: amplificador de potencia de 2 canales
Característica: 1U/amplificador digital/2 ohmios estable
Potencia de salida:
Potencia estéreo de 8 Ω (RMS): 4500 W x 2 canales
Potencia estéreo de 4 Ω (RMS): 8200 W x 2 canales
Potenci
Descripción


D2-4200 DSP FEATURE:
●2 Channel Class D Digital power amplifier 
●Mini 1U size,convenient for Touring Applications
●Suit for Stage Power Subwoofer speaker 18"/21"
●Work Under 2Ω steadily
●Imported Original Nippon Chemi-Con Capacitors
●Advanced stability GaN Transistors,Lower heat generation,Low noise,low distortion.
●Precise and Reasonable circuit structure,supper reliable sound
●Bridge-mode operation
●90V-270V Wide Range Operation voltage
●High Quality XLR/Speakon connectors
●Temperature protection;Over current protection;Short circuit protection built-in


 
 D SERIES HIGH POWER DIGITAL AMPLIFIER (Choose with or without DSP)
Model D2-3000 DSP D2-3500 DSP D2-4200 DSP D4-2000 DSP D4-3000 DSP
EIAJ Test Standard,1 kHz, 1% THD 8Ω/Stereo 2 x 3000W 2 x 3500W 2 x 4200W 4 x 2000W 4 x 3000W
4Ω/Stereo 2 x 5000W 2 x 6300W 2 x 7800W 4 x 3400W 4 x 5000W
2Ω/Stereo 2 x 7140W 2 x 7400W 2 x 8500W 4 x 4760W 4 x 6500W
8Ω/Bridge 1 x 10200W 1 x 12500W 1 x 15600W 2 x 6800W 2 x 10000W
4Ω/Bridge 1 x 14280W 1 x 14800W 1 x 17000W 2 x 9520W 2 x 13000W
 Alternating Current Power Supply
Power PFC Power
Rated power demand 100-240V±10%, 50/60Hz
Operation voltage 90V-270V
Power correction factor cos(φ) >0.95 @ >500W
Standby 47W and 0.8A
Gain,Sensitivity 32dB,35dB,38dB,41dB
Maximum Output Voltage/Current 185V/85A (370V in the BRIDGE MODE)
Power Comsumption 230V (115V in the BRIDGE MODE)
Temperature
Environment temperature 0°-45C / 32′-113*F
Cooling system Tunnel through cooing system
Performance
Frequency Response 20Hz - 20kHz (1W@8Ω,+05 dB)
Signal-to-Noise Ratio >110 dBA (20 Hz- 20 kHz A weighted)
Crosstalk >66 dB @ 1 kHz
Input Impedance 10 kΩ balanced
Total Harmonic Distortion(THD) <0.5% from 1 W to full power (Typitcal value<0.05%)
Intermodulation Distortion(IMD) <0.5% from 1 W to full power (Typical value< 0.05%)
Damping Factor (8 ohms) >5000 @ 20-200 Hz
Slew Rate 50V/μs @ 8Ω
 Front Panel
Indicator LED/per channel One PCS Green LED: the input signal of XLR ≥ -40dB;
Four pieces Green LED:
display the output signal(-20dB,-10dB,-5dB,-3dB)of SPEAKON
1 piece dual LED(Yellow and Red):
Protective state/Clip stste/Over heat/Over load
Power Switch Press "I"-on; Press "O"-off.
Dust-proof Two pieces dust-proof cotton,
it can take off to clean from the bottom of front pannel
 Application
Signal in-connection 4 Channel: One balanced XLR(with lock)female per channel;
2 Channel One balanced XLR(with lock)female
and one balanced XLR male per channel.
Signal out-connection One SPEAKON per channel connect to loudspeakers
Power cord Fited to the device, and the CSA(cross sectional area)of the cord is 3 x 2.5mm²,
and the card is 1.5 meters long.
Multiple-Functions Switch Two Sensitivity Switches. One Mode Switch and one Clip Switch.
 Structure(The size and weight depend on different series and shipping demand )
Dimensions 482 x 44 x 380mm³/482 x 44 x 470 mm³
Net weight 10Kg/12kg
Packing size 580 x 580 x 119mm³/615 x 615 x 119 mm³
Shipping weight 12Kg/14Kg


FRONT PANEL FEATURE




REAR PANEL FEATURE



Dimensions and Cooling system
NOTE:
The size is 437mm inside of the device(without the cover plate and front panel).The size is around 472mm of the complete device,but a little bit different size in the different front panel.Some series with different size that had not shown,please learn it in the parameter.


Tunnel through cooling system
Cold air comes in from the front panel of the equipment, forms a duct through the radiator to take the heat away and out from the rear panel of the equipment.


 



ALLDSP ALLControl 
The new D series digital amplifier also has the option to add a DSP function, Our D series DSP amplifier uses an ALLDSP system from Germany. It is suited for Windows, Mac and ios systems.
The application for iPad or iPhone can be downloaded and installed from the Apple Store.
App Name: ALLControl, Remind you it is Paid-for Software.(The software Password is Develo_p)

For the Remote Operation Software (Windows and Mac) and Manual, Please check the Download link or contact us!
Note that for a Windows computer, there are separate applications for Windows 32-bit and 64-bit.

 
Parameters of DSP Module
Digital signal processor
 64 bit multimode, 4 in and 4 o]ut
AD converter
120db Dynamic Range
DA converter
110db Dynamic Range
Storage preset
100
Signal input
Analog/optional Dante
Delay range
0-10ms
Equalizer
5-segment grouping equalization, 10 segment input/output equalization
Frequency division filter 
Linkwitz Reiley, Belsel, Butterworth
FIR filter
4x144taps
 
Attention: You cannot connect the unit to the network through the USB or Ethernet at the same time. You can only control the unit from one platform at the same time if you switch from one platform to another, you MUST shut down the control software at the previous platform first.
 
Local connectivity of the device to the control computer from a front-panel USB connector is also possible to download initial settings or as a fallback in case of network failure.


►Unit Window: Main Panel


Unit window shows the unit window from which all setup screens and options can be reached.Clicking the exit cross will close the software but leave the network Control program running.


Input Channel Settings Screen


Clicking on an Input channel number in the Unit window will bring up the input channel settings screen see Figure above. In this screen, individual input channels can be equalized and/or filtered.

Settings screen:
Filtering and EQ
Input channel transfer function curve
Screen expansion and legends
Input Gain, Mute
Delay, limiter, compressor
RMS compressor
 
●Screen expansion and legends
On the left-hand side of the graphical screen are four icons to help precise settings. The top Arrow icon expands the graphical screen to the size of the window.Clicking this icon again from the expanded screen expands it to the full display size. In either of the expanded settings, clicking the X-icon at the top left will collapse the graphical area to the default setting.

The T(ext) icon will place the frequency, Q and gain values of each EQ and filter setting in the graphical screen. 

For very accurate settings of EQ or filtering you can click the Looking Glass icon.
 
●Delay, limiter, compressor
Settings for channel delay, limiter (-48 to +24 dBu) and Limiter release rate (10 to 100 dB/s) settings.Plus a button to enter the rms compressor menus.Channel delay can be set in a variety of distance or time units from the drop-down list.
 
●Compressor settings window
Clicking on the compressor button brings up the compressor menu.
In the compressor menu you can set the parameters of the rms compressor.You can set the threshold, attack, hold, and release time, the compression ratio and the make-up gain.Next to the controls is a VU meter that also displays the gain reduction (GR). Be sure to use the ‘Back’ button to return to the output menu.


►Crossover Settings Window


When you click X-over in the left unit window function list, most of the screen is dedicated to the controls and indicators for setting up the cross over filters as shown in Figure.

Settings screen:
Graphical control
Filter type
Gain
Delay
Link
Mute, Phase Invert


►Output Channel Settings Screen


As shown in the picture above, faders are shown for each of the input channels. This will allow mixing each of the input signals to each individual Output channel. Even if Input channels are set to Linked in the Unit window, it is still possible here to mix individual Input channels to an Output channel in any desired ratio. Level setting are shown numerically below each fader. The available range is from -48 dB to 0 dB. As in other screen, double clicking a fader resets it to default.

A complete control screen is available for each Output channel. The graphical area reflects the Crossover settings for the channel in addition to any equalization settings set up in this screen, and is very similar to the available settings in the individual Input channel screens.The status of an element is always reflected in the blue on/off button next to each element.


Settings screen:
●Relationship between Input- and Output settings
●Output filtering and EQ
●Output channel transfer curve
●Delay, limiter, compressor
●RMS compressor
●Change / adjusting Values


►More Dsp Details please download:
D Series AllDSP ALLControl Software Download (64 bit)
D Series AllDSP ALLControl Software Download (32 bit)
 

Comentario

Suscríbete para actualizaciones de productos y promociones!